Objective To simultaneously high frequency Induction Soldering Brass Tubessolder to a brass water jacket assembly with induction heating. Equipment DW-HF-15KW Induction Heating Machine Key Parameters Power: 5 kW Temperature: 424°F (217°C) Time: 10 seconds until the alloy flows; 15 seconds to allow alloy to even out around the tube. TEST 1 Materials • Brass water … Read more
Objective Induction Soldering coaxial cable to connector ring and pin in two steps in under 5 seconds by reaching a temperature of 500°F (260°C) with induction heating. Equipment DW-UHF-6KW-III handheld induction heater Channel coil Materials • No-flux solder wire • Coaxial cable • Cable connector • Center pin Key Parameters Power: 3.0kW Temperature: 662°F (350°C) … Read more
Objective: Induction Soldering PCB Board with Copper Industry: Medical & Dental Materials: Flat copper pipes, PCB board Alloy: Low-temperature solder paste Equipment: DW-UHF-6KW-III handheld induction brazing machine Power: 3.88 kW Time: 8 secs. Coil: Coated custom-made coil. The Process: HLQ was contacted by a leading manufacturer of clinical diagnostic equipment who is striving to drive innovation in the Magnetic … Read more
Objective Induction Soldering coaxial cable to connector ring and pin in two steps in under 5 seconds by reaching a temperature of 500°F (260°C) with induction heating. Equipment DW-UHF-6KW-I handheld induction Soldering Heater Materials • No-flux solder wire • Coaxial cable • Cable connector • Center pin Key Parameters Power: 1.0kW Temperature: 662°F (350°C) Time: … Read more
Objective Induction Soldering cables to terminals in under 20 seconds using induction. Equipment DW-UHF-6KW-I handheld induction heater Materials • 0.078″2 (50mm2) cable terminal • 0.078″2 (50mm2) cable • Soldering alloy Sn60Pb38Cu2 Key Parameters Power: 2.8 kW Time: 15-20 sec Temperature: 500° F (260° C) Process: The 0.078″2 (50mm2) cable terminal is attached to 0.078″2 (50mm2) cable The assembly is positioned inside the … Read more
Objective: Test –Induction Soldering Copper Pipes to PCB Board Industry: Medical & Dental Materials: Flat copper pipes, PCB board Alloy: Low-temperature solder paste Equipment: DW-UHF-6KW-I Handheld Induction Heater Power: 1.88 kW Time: 15 secs. Coil: Coated custom-made coil. The Process: HLQ was contacted by a leading manufacturer of clinical diagnostic equipment who is striving to drive innovation in the Magnetic … Read more
Objective The objective of this application test is to determine heating times for induction soldering copper wire connectors onto a copper coaxial cable. The customer would like to replace hand soldering with soldering irons, with induction soldering. Hand soldering can be labor intensive, and the resulting solder joint is highly dependent on the skill of … Read more
Hig Frequency Induction Soldering Brass Corner Joint Objective Successfully solder two 45° brass corner joints. Equipment: DW-UHF-10kw induction soldering heater Materials StayBrite #8 silver solder supplied by customer Bridgit solder flux supplied by customer Brass corner joint Pancake coil Key Parameters Power: 5.5 kW Temperature: Approximately 550° F (288° C) Time: 20 sec Process: Flux … Read more
High frequency induction soldering copper tubing to brass valves Objective: Test: Induction Soldering copper tubing to brass valves Industry: HVAC Materials: Copper and brass pipes Equipment: DW-HF-25kw induction heating machine Power: 16 kW Temperature: 932oF (500oC) Time: 20 seconds Coil: Coated custom-made coil. The Process: This application request was brought to HLQ Induction Heating Power’s attention by a HVAC company. Their … Read more