Induction Heating Steel Handle For Bending

Induction Heating Steel Pliers Handles for Bending

Quick Answer

Induction heating steel handles for bending brings only the zone to be shaped up to forming temperature, so the part is not overheated.

In this HLQ case, a multi-turn helical coil heated a 3.75″ (9.53 cm) zone on one steel pliers handle at a time to 1200 °F (649 °C) in 30 seconds. The handles were 5″ (12.7 cm) long and 0.14″ (3.56 mm) thick. The coil ran at 50 kHz from a DW-HF-4.5kW induction heating system, with a remote heat station of two 0.33 µF capacitors (0.66 µF). The heated part then went to a press for final shaping. Precise zone heating gives higher quality than heating with a torch.

Flat steel handle glowing inside a multi-turn helical induction coil before bending
Flat steel part heated inside a multi-turn helical induction coil.

What is Induction Heating of Steel Handles for Bending?

The coil heats only the section of the handle that will be bent, so the steel is soft enough to form in a press while the rest of the part stays cooler. In this case, each handle is heated and formed one at a time.

Item HLQ case data
Objective Heat pliers for final shaping of the handles
Material Steel pliers handles, 5″ (12.7 cm) long, 0.14″ (3.56 mm) thick
Temperature 1200 °F (649 °C)
Frequency 50 kHz
Equipment DW-HF-4.5kW induction heating system with a remote heat station containing two 0.33 µF capacitors (0.66 µF total), plus a coil designed for this application
Coil Multi-turn helical coil heating a 3.75″ (9.53 cm) zone on one handle at a time; easy loading and unloading without rotating the part
Cycle Heated 30 seconds to 1200 °F, then transferred to a press and formed into the correct handle shape

Key Applications

Induction heating steel before forming: pliers handle 1200 °F at 30 s and steel shovel plates 950 °C in under 5 s
Application case diagram: two HLQ cases of heating steel before press forming.
Application HLQ case data Reference
Bending steel pliers handles 3.75″ zone, 1200 °F, 30 s, then press This case
Hot forming steel shovel plates 4 plates to 950 °C, target under 5 s, DW-HF-45KW, then press steel plate shovels hot forming with induction preheating
Heating bar and rod ends for forming Channel and solenoid coils induction heating the end of rods, billets and bars
Rivet head forming 700 °C in 10–15 s induction heating rivet ends
Pipe bending Steel pipe and tube induction pipe bending machine

Suitable Materials

Material Notes
Steel pliers handles 5″ long, 0.14″ thick; formed at 1200 °F (this case)
Steel plates Hot formed into shovels at 950 °C (HLQ shovel case)
Steel tool handle
Steel tool handle.

Working Principle

Principle of induction heating pliers handles: 50 kHz supply, remote heat station 0.66 µF, multi-turn helical coil heating a 3.75 inch zone to 1200 °F
Principle diagram (schematic, not to scale).
  1. The power supply drives the remote heat station (2 × 0.33 µF) and the helical coil at 50 kHz.
  2. One handle is inserted into the coil; the coil allows loading and unloading without rotating the part.
  3. Eddy currents heat the 3.75″ zone inside the coil to 1200 °F in 30 seconds.
  4. The part is transferred to a press and formed.

More: induction heating coil design and skin effect in induction heating.

Technical Specifications

Parameter Value
Part Steel pliers handles
Handle length 5″ (12.7 cm)
Thickness 0.14″ (3.56 mm)
Heated zone 3.75″ (9.53 cm) on one handle at a time
Temperature 1200 °F (649 °C)
Heating time 30 s
Frequency 50 kHz
Capacitors 2 × 0.33 µF (0.66 µF)
Coil Multi-turn helical
Forming Press

Recommended Model Selection

The case equipment was a DW-HF-4.5kW induction heating system at 50 kHz. Several pliers handles can be heated at the same time with a higher-kW power supply. HLQ DW-HF models:

Model Power Input current Supply
DW-HF-15KW 15 kVA 32 A 1-phase 220 V
DW-HF-25KW 25 kVA 23 A 3-phase 380 V
DW-HF-35KW 35 kVA 51 A 3-phase 380 V
DW-HF-45KW 45 kVA 68 A 3-phase 380 V
DW-HF-60KW 60 kVA 105 A 3-phase 380 V
DW-HF-80KW 80 kVA 130 A 3-phase 380 V

Smallest DW-HF model: DW-HF-15 high frequency induction heater. All models: HLQ induction heating device models.

Process Workflow

Pliers handle bending workflow: insert handle, heat 3.75 inch zone 30 s to 1200 °F, transfer to press, form, repeat for second handle
Process flow chart from the HLQ pliers handle case.
Step Action
1 Insert one handle into the helical coil
2 Heat the 3.75″ zone for 30 s
3 The zone reaches 1200 °F (649 °C)
4 Transfer the part to the press
5 Form the handle into its final shape
6 Heat and form the second handle
7 Formed pliers go to the next step

Cell layout

Pliers handle heating and bending cell layout: induction power supply, remote heat station, helical coil, operator, press
Layout diagram (schematic, not to scale).

Common Problems and Solutions

Problem Cause Solution
Part overheated Torch heats beyond the zone Coil heats only the 3.75″ zone (case result)
Slow loading Part must be rotated into the coil Coil designed for loading and unloading without rotating the part
Uneven forming results Heating time varies Fixed 30 s heating time for every handle
Output too low One handle at a time Higher-kW supply to heat several handles at once

Engineering Selection Guide

Factor What to confirm Why it matters
Part geometry Length, thickness, zone to bend Coil size and length
Forming temperature For example, 1200 °F (649 °C) Power and time
Parts heated at once One or several Power rating
Handling Manual or automated transfer to the press Coil opening and layout
Supply 1-phase or 3-phase Model choice

Advantages and Limitations

Advantages Limitations
Precise zone heating avoids overheating the part The coil is designed for each part
Higher quality than torch heating One handle at a time with a small supply
Easy loading without rotating the part The part must be transferred to the press
Repeatable 30 s cycle —

Why Choose HLQ?

Strength Evidence
Forming experience Pliers handles, shovel plates, bar and rivet ends
Practical coils Helical coil that loads without rotating the part
Scalable Higher-kW supplies for several parts at once
DW-HF series 15–160 kVA
Quality Zone heating, no overheating

10 Core FAQs

1. What is heated in this application?

A 3.75″ (9.53 cm) zone on one steel pliers handle at a time, before final shaping.

2. What size are the handles?

5″ (12.7 cm) long and 0.14″ (3.56 mm) thick.

3. What temperature is used?

1200 °F (649 °C).

4. How long does heating take?

30 seconds per handle.

5. What frequency was used?

50 kHz.

6. What is in the heat station?

Two 0.33 µF capacitors, 0.66 µF in total.

7. Which coil was used?

A multi-turn helical coil that allows easy loading and unloading without rotating the part.

8. What happens after heating?

The part is transferred to a press and formed into the correct handle shape.

9. Can several handles be heated at once?

Yes, with a higher-kW power supply.

10. What is needed for a quotation?

The part drawing and material, the zone to be heated, the forming temperature, the number of parts per hour, and the available supply.

HLQ-Induction-Heating-Steel-Handle-Bending-Brochure

=